The outdoor bamboo floor is made of high-quality outdoor heavy bamboo. The material is made by cutting the bamboo into long thin bamboo strips, through constant temperature dehydration, high-temperature cooking, high-pressure carbonization strong gluing. It has the characteristics of wear-resistant, corrosion-resistant, moth proof high stability. Its compressive strength is twice that of the general wood, its tensile strength is 8 times that of the general wood. It can be used for outdoor floors households Production of exterior wall panel, outdoor railing, outdoor furniture other products.

China is the country with the most abundant bamboo resources in the world, its distribution is relatively centralized, which is convenient for centralized development. In addition, the growth cycle of bamboo is short the timber is fast. The outdoor heavy bamboo processed by bamboo is the raw material to replace the outdoor high-grade hardwood limited by environmental resources, it is a good green building material. At present, it has become a new favorite in many high-end properties, outdoor landscapes private courtyards. At present, our factory is a professional outdoor heavy bamboo floor manufacturer in China.

Advantages of outdoor heavy bamboo floor: it has the characteristics of high hardness, high strength, corrosion resistance, wear resistance, termite resistance, fire resistance flame retardant, is one of the excellent outdoor floors. It has excellent dimensional stability, high compressive strength high density, which makes it easy to cope with the harsh outdoor humid heat, dry cold other special environments.

Outdoor bamboo wood paving steps

1. Moisture proof treatment

First, the floor to be laid shall be covered with a layer of moisture-proof materials, such as linoleum, plastic film, etc. The moisture-proof materials shall be complete as far as possible, the damaged parts joints shall be covered repeatedly. The purpose of laying the damp proof course is to prevent the condensation of water vapor on the ground the water vapor penetrating through the capillary directly contacting the back of the floor. let it pass through the edge seam left at the foot of the wall around, send it out into the air. Moistureproof treatment is particularly necessary for the decoration of new buildings.

2. Laying keel

Bamboo floor is different other flexible floor, it must be supported fixed by keel.

First of all, we should choose the materials to make keels. Generally speaking, ordinary wood can be used to make keels, such as pine, fir some broad-leaved trees, etc., but the wood that is easy to mildew has strong nail holding power is preferred. The specification of keel is about 30mm × 30mm, the length is any length. It can be sawn lengthened according to the indoor size. The wood used as keel must be dried manually naturally, then planed to the same thickness by four side planing pressing machine. Then there is the nail keel. The keel shall be laid in parallel according to the width direction of the room, with a distance of about 300cm, depending on the length of the floor. However, it should be noted that both ends of the floor must be built on the keel to avoid suspension. After the keel is positioned, level it with a horizontal ruler, level it with a wooden block, then use a 5cm cement nail to firmly nail the keel to the cement ground.

Some users like to nail another layer of plywood MDF on the keel. If the floor height economic conditions of the house are allowed, it can also be completely nailed without affecting the use.

3. Pave the floor

The bamboo floor assembly generally adopts the dislocation method, that is, the joint joints of tenon groove at both ends are staggered with each other, the joint joints are in the same straight line with each other. This is similar to the method used in building brick walls. This assembly method can make the joint evenly distributed on the plane increase the three-dimensional sense of the plane.

When the width length of the floor are multiple of the indoor size, the floor can be sawed sawed, but a layer of varnish shall be applied on the saw mouth to keep the floor closed to water. The method of fixing the floor keel is to use a 2.5cm long iron nail at the root of the tenon along the length of the floor, to nail penetrate the floor at an angle of 45 ° to the depth of the keel, so that the floor the floor are closely integrated into a "whole". Before using nails to drive into the floor, a pilot hole must be drilled with a small drill to prevent the nails cracking the floor. Because bamboo has no transverse fiber, it is easy to crack.

Another problem needs to be noted is that the floor should be 1cm ~ 2cm away the wall around the room, so as to prevent the water in the wall entering the floor. The left gap can be covered with corner line without affecting the appearance.